项目名称：哈尔滨麦硕国际教育社区展示中心照明工程

　　此项目为2021阿拉丁神灯奖工程类参评项目

　　申报单位：北京光影国际照明设计

　　项目地址：黑龙江哈尔滨北智谷大街与光宇一路交叉口

　　设计单位：北京光影国际照明设计

　　施工单位：北京市宝维智能照明工程技术有限公司

　　业主单位：黑龙江省宝唐房地产开发有限公司

　　项目简介

麦硕·禮城项目以国际教育聚集为核心，以现代科技和信息技术为手段，致力于建设一个国内领先、国际知名的教育生态体系，构建东北亚以教育为核心的智慧城市社区

其中展示中心整体采用庄重与古朴的英式建筑风格，简洁的柱体与拱形建筑结构，赋予建筑动态的韵律与美感。

With international education gathering as the core and modern technology and information technology as the means, Maishuo · Licheng Project is committed to building a domestic leading and internationally renowned education ecological system and building an education-centered smart city community in Northeast Asia.

Among them, the exhibition center adopts the solemn and simple British architectural style, and the simple column and arch structure endows the building with dynamic rhythm and beauty

项目宣传视频：

　　照明技术指标

LED贴片灯：功率12W 色温3000K 数量162米
LED洗墙灯：功率24W 色温3000K 数量34米
LED投光灯：功率6W 色温3000K 数量65套
LED投光灯：功率12W 色温3000K 数量24套
LED地埋灯：功率24W 色温3000K 数量36套
艺术吊灯：功率40W 色温3000K 数量4套

供配电系统

1．本工程为220/380V供配电系统，采用放射式供电方式；
2．计量：夜景照明配电系统均在上级配电箱（柜）进行计量；
导线选择和线路敷设
所有供配电线路和控制线路必须按设计规范要求穿厚壁热镀锌钢管或金属线槽敷设，任何地方都不能出现裸导线的情况，更不能把供电线路直接埋在地面和墙体内；
2. 照明线路采用WDZ-YJY-3*2.5电力电缆；低压线路采用ZR-RVV阻燃铜芯电缆；
3. 电缆分支或有破开处须设防水接线盒并离地0.3m安装；敷设管线应在适当位置加拉线盒（直线：30m，一个弯：20m，二个弯：15m，三个弯：8m）；4.管线埋地敷设时埋地深度不小于0.7m，在寒冷地区电缆宜埋设于冻土层以下；所有穿过建筑物伸缩缝、沉降缝、后浇带的管线应按《建筑电气安装工程图集》中有关作法施工；

设备要求：
1）照明设备所有带电部分应采用绝缘、遮拦或外护物保护，距地面2.8m以下的照明设备应使用工具才能打开外壳进行光源维护；
2）室外安装照明配电箱与控制箱等应采用防水、防尘型，防护等级不应低于IP54；
3）室外配电箱内元器件应考虑室外环境温度、湿度的影响，距地面2.8m以下的电气设备应借助于钥匙或工具才能开启；
4）LED灯具应选用专用开关电源，LED灯具输入电压应与开关电源输出电压一致；
5）在正常视角范围内的光源可直视灯具，必须采取有效防眩光措施；
6）对人员可触及的照明设备，当表面高于60℃时，必须采用隔离保护措施；
7）灯具、附件及电气设备满足项目所在地气候环境条件下正常工作；
8）夜景照明灯具防护等级必须满足消防安全要求；室外雨棚嵌入式筒灯防护等级不低于IP44,水下灯防护等级不低于IP68等；
9)所有I类灯具均设置地线接地保护;
10)灯具功率因数不应低于0.9，以减少线路损失，确保供电质量及光源效率.

时间控制器系统要求：

1）开、关时间任意可调；
2） 已调好的开、关时间不受停电影响，自动记忆；
3）每天可做十次开、关动作，开、关时间一周内可任意编程；
4）可自动，也可手动控制，设有自动保护装置；
5）内消耗功率低；

施工安装要求：
1）夜景照明灯具及配套电器、开关电源、控制器等电气设备禁止安装在可燃材料表面；
2）开关电源、各种控制器必须按照施工设计规范要求安装在金属外壳的箱体内，不得埋在地面和墙体内；
3）灯具的电缆电线接头应端子连接或涮锡连接、并做防水处理；
4）为了保证安装强度和防止雨水腐蚀，灯具安装支架、固定螺丝应全部为不锈钢或铝合金材质；
5）灯具、管线及电气设备布置不得影响消防安全疏散与救援；
6）室外灯具外壳颜色应与安装部位表面颜色协调；外立面夜景照明灯具及布线应做到不外露、不易触碰到，主立面严禁外露；
7）所有供配电线路和控制线路必须按设计规范要求穿厚壁热镀锌钢管或金属线槽敷设，任何地方都不能出现裸导线的地方，亦不可直埋于地面或者墙体内；
8）施工满足项目所在地的地方标准及施工规范要求；

LED patch lamp: power 12W, color temperature 3000K, quantity 162m

LED wall washing lamp: power 24W color temperature 3000K quantity 34m

LED projection light: power 6W color temperature 3000K Quantity 65 sets

LED projection light: power 12W color temperature 3000K quantity 24 sets

LED buried light: power 24W color temperature 3000K quantity 36 sets

Art chandelier: power 40W color temperature 3000K quantity 4 sets



Power supply system

1. This project is 220/380V power supply and distribution system, using radiation power supply mode;

2. Metering: Nightview lighting distribution system are measured in the superior distribution box (cabinet);

Conductor ion and circuit laying

All power supply and distribution lines and control lines must be laid through thick wall hot dip galvanized steel pipe or metal trough according to the requirements of the design specification. Bare wires can not appear anywhere, let alone the power supply lines directly buried in the ground and walls;

2. WDZ-YJY-3*2.5 power cable is adopted for lighting circuit; ZR-RVV flame retardant copper core cable for low voltage line;

3. Water proof junction box shall be set up at cable branch or broken place and shall be installed 0.3m above the ground; The pipeline should be laid in the appropriate position of the wire box (straight line: 30m, one bend: 20m, two bend: 15m, three bend: 8m); 4. The buried depth of the pipeline should not be less than 0.7m when it is laid in ground. In cold areas, the cable should be buried under the permafrost; All the pipelines through the expansion joints, settlement joints and post-cast belts of the building shall be constructed according to the relevant practices in the Atlas of Building Electrical Installation Engineering;

Equipment requirements:

1) All live parts of the lighting equipment should be protected by insulation, shielding or external protection. The lighting equipment below 2.8m the ground should use tools to open the shell for light source maintenance;

2) Outdoor lighting distribution box and control box should be waterproof and dustproof, and the protection grade should not be lower than IP54;

3) The components in the outdoor distribution box should consider the influence of outdoor environment temperature and huity, and the electrical equipment below 2.8m the ground should be opened with the help of keys or tools;

4) LED lamps should use special switching power supply, and the input voltage of LED lamps should be consistent with the output voltage of the switching power supply;

5) The light source within the normal viewing Angle can look directly at the lamp, and effective anti-glare measures must be taken;

6) For lighting equipment accessible to personnel, when the surface is higher than 60℃, isolation protection measures must be adopted;

7) The lamps, accessories and electrical equipment should work normally under the climatic and environmental conditions of the project location;

8) The protection level of nightview lighting fixtures must meet the fire safety requirements; The protection level of outdoor canopy embedded downlight should not be lower than IP44, and the protection level of underwater light should not be lower than IP68;

9) All Class I lamps are equipped with ground wire grounding protection;

10) The power factor of the lamp should not be less than 0.9 to reduce the line loss and ensure the quality of power supply and the efficiency of the light source.

Time controller system requirements:

1) Opening and closing time can be adjusted;

2) The adjusted on and off time is not affected by power failure, and it can be automatically remembered;

3) Can do 10 times a day on and off action, on and off time within a week can be arbitrary programming;

4) It can be controlled automatically or manually, and equipped with automatic protection device;

5) Low internal power consumption;

Construction and installation requirements:

1) Nightview lighting lamps and supporting electrical appliances, switching power supply, controllers and other electrical equipment are prohibited to be installed on the surface of combustible materials;

2) Switching power supply and various controllers must be installed in the box of the metal shell in accordance with the requirements of the construction design specification, and shall not be buried in the ground and wall;

3) The cable and wire connectors of lamps and lanterns should be connected with terminals or dipping tin, and waterproof treatment;

4) In order to ensure the installation strength and prevent rain corrosion, the mounting bracket and fixing screws of the lamp should be made of stainless steel or aluminum alloy;

5) Layout of lamps, pipelines and electrical equipment shall not affect fire safety evacuation and rescue;

6) The exterior lamp shell color should be in harmony with the surface color of the installation part; External facade night lighting lamps and wiring should be not exposed, not easy to touch, the main facade is strictly prohibited exposure;

7) All power supply and distribution lines and control lines must be laid through thick-walled hot-dip galvanized steel pipes or metal grooves according to the requirements of the design specifications. No bare wires can be found anywhere, nor can they be directly buried in the ground or walls;

8) The construction shall meet the local standards and construction specifications of the project site;

　　节能措施及效果

　　项目设计：在建筑需要的位置赋予灯光，用适量的灯具与建筑的完美结合。
产品运用：贴合绿色照明，每款灯型确保功率合适，无运用大功率灯具；同时极大地减少了视觉上的曝光点及过度照明。
控制模式：采用成熟的时间控制模块，将建筑照明分为夜晚和深夜两种模式（夜晚灯光状态全开深夜只保留基础功能），照明内消耗功率低；

Project design: lighting is given to the location needed by the building, with the perfect combination of the right amount of lamps and buildings.

Product application: fit green lighting, each lamp type to ensure appropriate power, no use of high-power lamps; It also greatly reduces visual exposure points and overillumination.

Control mode: a mature time control module is adopted to divide the lighting of the building into two modes: night and late night (the lighting is fully switched on at night and only the basic functions are retained at night). The power consumption in lighting is low.

　　照明设计创新点

　　用温暖光感，优雅的姿态，内敛不张扬，内涵不奢侈，充满文学气息，呈现出绅士风范；
建筑以竖向灯光为主，体现阵列感，二层选用较小的灯体，灯具完全隐藏起来，地面灯具采用深度防眩，避免走进后灯光的直射，巧妙运用灯光的穿透性，与屋檐形成较好的晕染效果。
With warm light sense, elegant posture, introverted not publicity, connotation is not luxury, full of literary atmosphere, showing a gentleman style;

The building is dominated by vertical lights, reflecting the sense of array. On the second floor, smaller light bodies are ed, and the lamps are completely hidden. The ground lamps adopt deep anti-dazzle to avoid the direct light after walking into the building.

　　项目实际运行评价

　　申报单位

公司成立十年以来，由郑志伟先生领衔二十余位顶尖团队，致力于光环境设计与研究。以国际视野和世界领先的灯光技术方案，创造极具视觉艺术及商业价值的光影作品。

专注于城市地标、商业综合体、星级酒店、文旅小镇、城市景观等全球精品项目灯光设计，光影国际是万达、恒大、泰禾、佳兆业等众多地产的优秀合作伙伴，设计了如青岛2008迎奥城市夜景、重庆江北区城市夜景、天津万达中心、北京合生汇、成都银泰城、恒大海花岛、广州融创主题乐园、深圳佳兆业国际主题乐园等众多国内知名项目。光影国际参与并制定了万达室内乐园基础照明设计标准、万达A-02，B02，B03，B-02，B-04BIM标准、光之变革美术馆篇照明质量评估方法与体系研究、博物馆照明设计标准等。作品屡获国际、国内众多大奖，致力于打造中国第一灯光设计品牌。

Since the establishment of the company ten years ago, Mr. Zheng Zhiwei led more than 20 top team, committed to the light environment design and research. With the international vision and the worlds leading lighting technology solutions, to create great visual art and commercial value of light and shadow works.

Focused on the city landmarks, commercial complexes, star hotel, tour town, urban landscape, such as global high-quality goods project lighting design, lighting, Evergrande, taihe, wanda international is jia zhaoye numerous excellent partner of real estate, such as design such as Qingdao 2008 to meet the urban night scene, night at chongqing jiangbei city, tianjin wanda center, Beijing, chengdu Yintai connation remit city, constant melting sea island, guangzhou a theme park, shenzhen jia zhaoye international theme park, and many other famous domestic projects. Lighting International participated in and formulated basic lighting design standards for Wanda Indoor Park, Wanda A-02, B02, B03, B-02, B-04BIM standards, research on lighting quality evaluation methods and systems for the Light Revolution Museum, and lighting design standards for museums, etc. Works have won many international and domestic awards, is committed to building Chinas first lighting design brand.